2pcs 300Mbps Outdoor Wireless Bridge 5.8GHz 3KM WIFI Router Extender Access Point CPE For Elevator Monitoring Project CF-E113A

CF-E113A is a 5.8GHz anti-interference elevator wireless monitoring bridge (one pair). It has the characteristics of anti-interference, signal stability, one-key pairing, 300Mbps transmission, etc. The transmission distance can reach about 3 kilometers in the presence of obstacles.

Specifications:

1. 5.8GHz frequency band, 300Mbps transmission rate, strong anti-interference ability

2. Qualcomm 560Mhz frequency industrial-grade CPU;

3. compliant with IEEE802.11a/n standard

4. Built-in 11dBi gain antenna, wide transmission and reception rate;

5. built-in PA, strong signal, high-speed transmission

• One-click pairing

• High power Built-in PA

• Preferred choice smooth channel

• 3km stable transmission

• 5.8GHZ Anti-interference

• 11dbi High gain antenna

Toggle switch, One-click pairing

Say goodbye to complex settings , Easy to set up

No wiring required

With one pair of COMFAST wireless CPE , it's so easy to deal

6 core advantages remove all worries of engineering users

——3km stable transmission

CF-E113A CPE set supports video data transmission in about 3km . It can realize scattered video surveillance of different factories and multiple construction sites , docks ,parks , etc , and can be viewed and centralized in real time in the monitoring center

——Enjoy 5.8GHZ Anti-jamming channel

2.4GHZ frequency band is prone to disconnection ,instability , data loss etc . due to too much interference.The CF-E113A CPE works in the 5 , 8GHZ band and has multiple idle channels with strong anti-interference

——Precision protection , outdoor application

Professional outdoor engineering plastic shell , Strict silk stitching.Dustproof , waterproof , adapt to bad weather such as wind,frost , rain and snow

——Signal tracking precise location

The CPE comes with signal indicator , users can adjust the angel of the CPE according to the signal strength , easy to achieve high quality of long-range wireless transmission effect

——High gain antenna , Transmission guarantee

With built-in 11dbi high gain directional antenna to ensure the transmission distance and stable signal

——Hide SSID Refuse other people to get free wifi

COMFAST Wireless CPE support SSID broadcast hide ,can easy solve the troubles of network security and ensure the engineering stability

Application

Elevator/Factory/Diver School/Shipside/Port/Oilfield

Outdoor transmission application diagram

Point to Point Connection Diagram

Multiple cameras connection way 1 : Connection the cameras to the switch ,then connect with the COMFAST CPE It will transmit the data through two CPE

Multiple cameras connection way 2 : If the distance among the cameras is so far , each camera is configured with two CPES . The control center connect CPE with AP mode through the switch , then connect with the NVR

Point to Muti-point Connection Diagram

If the angle of camera and monitor center is less than 60 degree , there can consider one point to multi point connection . lt can reduce CPES with the transmitting mode , which can save project cost a lot . Pls pay attention that it has to meet the angle and Broadband requirement

Elevator Monitoring Application diagram

Product Details

Installation guide

Installation guide for tie

• 1.Insert two ties A into two holes B as picture shows . It can be adjusted by Pole .

• 2.Install the main device on the pole and then fasten the ties A by pliers

• 3.Press the fastener E and take off the cover C Then insert the cable D into the RJ45 port and cover it to

Installation guide for mount bracket

• 1.Insert two ties A into two holes B as picture shows . It can be adjusted by Pole

• 2.First install the tie A to the mount bracket . Then install the main device on the pole of the mount bracket and then fasten the ties A pliers

• 3.Press the fastener E and take off the cover C Then insert the cable D into the RJ45 port and cover it to finish the installation

Installation guide for Nail Mount

• 1.F and G are the nail hole position

• 2.Fix the main device by two nails rope

• 3.press the fastener E and take off the cover C Then insert the cable D into the RJ45 port and cover it to finish the installation