Newest Spectrum analyzer Handheld tiny Spectrum Anslyzer Tinysa Ultra 4" Display 100kHz to 5.3GHz 32GB Card Version V0.4.5.1
Description
2023 New Handheld Tiny Spectrum Analyzer TinySA ULTRA 4" Display 100kHz to 5.3GHz with 32GB Card Version V0.4.5.1
Specification：
Parameter | Specification |
Display size | 4” TFT LCD (480×320) |
Max low input frequency | 800MHz, 6GHz in Ultra mode |
Resolution filters in 1,3,10 steps | from 200Hz to 850kHz |
Max output frequency | Sinus up to 800MHz, Square wave up to 4.4GHz |
output level | -104dBm to -16dBm |
Ultra mode | Level calibrated up to 5.3GHz |
Internal LNA gain | 20dB up to 4GHz |
Displayed points per scan | max 450 |
0-350MHz scan time | 165ms |
Shortest zero span time | 17ms |
DANL at 100MHz | -153dBm/Hz (LNA Off) / -169dBm/Hz (LNA On) |
DANL degrading in ultra mode | 10dB above 2.5GHz, 25dB above 5.3GHz |
Phase noise at 10kHz offset | -92dBc/Hz |
Phase noise at 100kHz offset | -110dBc/Hz |
Input 1dB compression level | +0.5dBm (LNA Off) / -26.5dBm (LNA On) |
IIP3 without LNA | +18dBm (at least 2MHz apart) / 0dBm (500Hz apart) |
IIP3 with LNA | -8dBm (at least 2MHz apart) |
Frequency stability | <1ppm ( -10℃ ~ +55℃) |
SD card slot | micro SD card |
Audio out | 3.5mm headphone plug |
FW update mode activation | Push jog button before switch on |
Maximum current consumption | 330mA |
Maximum charging current | 1300mA |
Battery | Li-polymer 3.7V 3000mAh |
RF connectors | SMA female |
Communication Interface | USB-CDC(Type-C)，UART-TTL(2.54mm Connector) |
Appearance Size | 117x72x23mm (Excluding protruding parts) |
TinySA model comparison table：
tinySA | tinySA Ultra | |
Display size | 2.8 inch | 4 inch |
Max low input frequency | 350MHz | 800MHz, 6GHz in Ultra mode |
High input range | 240MHz - 960MHz | Not available |
Resolution filters in 1,3,10 steps | from 3kHz to 600kHz | from 200Hz to 850kHz |
Max low output frequency | 350MHz | Sine wave up to 800MHz, Square wave up to 4.4GHz |
Low output level | -76dBm to -7dBm | -104dBm to -16dBm |
High output frequency range | 240MHz - 960MHz | Not available |
High output level | -32dBm to 16dBm | Not available |
Ultra mode | Not available | Level calibrated up to 6GHz |
Internal LNA gain | Not available | 20dB up to 4GHz |
Internal step attenuator | Normal: 0-31dB, High: NA | 0-31dN |
Displayed points per scan | max 290 | max 450 |
0-350MHz scan time | 405ms | 165ms |
Shortest zero span time | 1.8ms | 17ms |
DANL low input at 100MHz | -146dBm/Hz | -153dBm/Hz (LNA Off) / -169dBm/Hz (LNA On) |
DANL high input at 880MHz | -163dBm/Hz | Not available |
DANL degrading in ultra mode | 10dB above 2.5GHz, 25dB above 5.3GHz | |
Phase noise at 10kHz offset | -83dBc/Hz | -92dBc/Hz |
Phase noise at 100kHz offset | -98dBc/Hz | -108dBc/Hz |
Low input 1dB compression level | -0.5dBm | +0.5dBm (LNA Off) / -26.5dBm (LNA On) |
IIP3 without LNA | +24dBm | +18dBm (at least 2MHz apart) / 0dBm (500Hz apart) |
IIP3 with LNA | Not available | -8dBm (at least 2MHz apart) |
SD card slot | Not available | micro SD card |
Audio out | Not available | 3.5mm headphone plug |
FW update mode activation | Via DFU menu | Push jog button before switch on |
AM modulation depth | Fixed 30% | 10% and 100% |
FM deviation | 4kHz or 75kHz | 1kHz to 300kHz |
Modulation frequency | 50Hz to 5kHz | 50Hz to 5kHz(AM) or 1kHz(FM) |
Package includes:
Host (with 3000mAh battery, 4"display) x 1
USB Type-C data cable x1
30cm ALSR100 SMA cables x2
SMA-SMA barrel connector x1
Antenna with SMA connector x1
Lanyard and touch plectrum x1
32GB MicroSD card(plugged in the host) x1
Upgraded Hand held tiny Spectrum analyzer TinySA 2.8" display 100kHz to 960MHz with ESD proteced Version V0.3.1_E
Specification
User interface:
* Display resolution 320*240 pixels
* Screen diagonal 2.8"
* 16 bits per RGB pixels
* Resistive touch control
* Jog switch control
* USB serial port control
* Optional TTL USART port (SW not yet implemented) on the internal PCB
* Linear power supply to avoid switching noise.
*Add port ESD protection to upgrade version（V0.3.1_E）
The input/output specification of the tinySA is split over the 4 modes
Low input mode spec:
* Input frequency range from 100kHz to 350MHz
* Input impedance 50 ohm when input attenuation set to 10dB or more.
* Selectable manual and automatic input attenuation between 0dB and 31dB in 1 dB steps
* Absolute maximum input level without attenuation of +10dBm
* Absolute maximum input power with 30dB attenuation of +20dBm for short period
* Input Intercept Point of third order modulation products (IIP3) with 0dB attenuation of +15dBm
* 1dB compression point at +2dBm with 0dB attenuation
* Power detector resolution of 0.5dB and linearity versus frequency of +/-1dB
* Absolute power level accuracy after power level calibration of +/- 1dB
* Lowest discernible signal using a resolution bandwidth of 30kHz of -102dBm
* Frequency accuracy equal to the selected resolution bandwidth
* Phase noise of -90dB/Hz at 100kHz offset and -115dB/Hz at 1MHz offset
* Spur free dynamic range when using a 30kHz resolution bandwidth of 70dB
* Manually selectable resolution filters of 3, 10, 30, 100, 300, 600kHz. Automatic selection of one of the 57 resolution filters.
* On screen resolution of 145 or 290 measurement points.
* Scanning speed of over 1000 points/second using largest resolution filters.
* Automatic optimization of actual scanning points to ensure coverage of the whole scan range regardless of the chosen resolution bandwidth
* Spur suppression option for assessing if certain signals are internally generated or actually present in the input signal
High input mode spec:
* Input frequency range from 240MHz to 960MHz
* As there is no input bandfilter strong signals outside the 240MHz to 960MHz range can cause distortion of the in band signals
* Absolute maximum input level without attenuation of +10dBm
* Input Intercept Point of third order modulation products (IIP3) of -5dBm
* 1dB compression point at -6dBm with 0dB attenuation
* Power detector resolution of 0.5dB and linearity versus frequency of +/-1dB
* Absolute power level accuracy after power level calibration of +/- 1dB
* Lowest discernible signal using a resolution bandwidth of 30kHz of -115dBm
* Frequency accuracy equal to the selected resolution bandwidth
* Spur free dynamic range when using a 30kHz resolution bandwidth of 50dB
* Selectable (automatic and manual) resolution filters of 3, 10, 30, 100, 300 and 600kHz
* Optional 25dB to 40dB frequency dependent input attenuator. The power level error with this attenuator activated increases to +/- 15dB
* On screen resolution of 145 or 290 measurement points.
* Scanning speed of over 1000 points/second using largest resolution filters.
* Automatic optimization of actual scanning points to ensure coverage of the whole scan range regardless of the chosen resolution bandwidth
Low output mode spec:
* Sinus output with harmonics below -40dB of fundamental
* Output frequency range from 100kHz to 350MHz
* Output level selectable in 1dB steps between -76dBm and -6dBm
* Optional AM, narrow FM and wide FM modulation or slow sweep over selectable frequency span
High output mode spec:
* Square wave output
* Output frequency range from 240MHz to 960MHz
* Output level selectable in variable increments between -38dBm and +13dBm
* Optional narrow FM and wide FM modulation or slow sweep over selectable frequency span
Reference generator spec:
* Optional square wave output with fundamental at -25dBm connected to high input/output
* Frequency can be set to 1MHz, 2MHz, 4MHz, 10MHz, 15MHz or 30MHz.
Battery spec:
* Charging time max 1 hour on 500mA minimum USB port or USB charger
* Operation on fully charged battery for at least 2 hours
Package inclued:
TinySA 2.8" Spectrum analyzer *1
20cm sma-sma rg174 rf cabe *2
USB Type-C Data Cable *1
Hand rope *1
SMA female to female connector *1
SMA telescopic antenna *1
Related Products
New Spectrum Analyzer Tiny Spectrum Analyzer Tinysa Ultra 4 Inch Display With Battery 100Khz To 5.3Ghz With 32GB Card
